GF Signet 3-9900-1BC Batch Controller System
9900 batch controller with stored batches, remote control and relays
SKU:3-9900-1BC
Model Number: 3-9900
$1833.000
GF Signet 3-9900-1BC is a batch controller system that stores up to 10 batch sizes and K-factors, supports remote batch control and provides programmable relays.
WHERE TO BUY?
GF Signet 3-9900-1BC Batch Controller System
The GF Signet 3-9900-1BC combines the 9900 transmitter platform with batch-control capability for repeatable liquid batching and blending applications.
- Manufacturer part number: 3-9900-1BC
- Stores up to 10 batch sizes with customizable batch names
- Supports separate K-factors for different batches
- Remote start, stop and resume control terminals
- Three programmable relays
- Two-stage control can help reduce overfill or water hammer
- Accepts compatible frequency, S3L and 4 to 20 mA inputs
The 3-9900-1BC is suited to process skids, chemical addition and other applications that need local batch setup with automation-friendly control options.
| Input Channels | One |
|---|---|
| Accuracy | ±0.2% |
| Terminal Blocks | Pluggable screw type 14 AWG max wire gauge |
| Window | Shatter-Resistant Glass |
| Keypad | 4 buttons, injection-molded silicone rubber seal |
| Display | Backlit, 7- and 14-segment |
| Indicators | Dial-type digital bar graph |
| Update Rate | 1 s |
| LCD Contrast | 5 settings |
| Enclosure Size | 1/4 DIN |
| Mounting Panel | 1/4 DIN, ribbed on four sides for use with mounting bracket for panel mount installations |
| Mounting Panel Wall | Large enclosure (sold as an accessory) that encases the panel mount transmitter |
| Backlit LCD | -10 °C to 70 °C / 14 °F to 158 °F |
| Storage Temperature | -15 °C to 70 °C / 5 °F to 158 °F |
| Operating Temperature | -10 °C to 70 °C / 14 °F to 158 °F |
| Relative Humidity | 0 to 100% condensing for front only; 0 to 95% non-condensing for back side |
| Maximum Altitude | 4,000 m (13,123 ft) |
| Enclosure Rating | Designed to meet NEMA 4X/IP65 (front face only) |
| Input power DC | 24 VDC input; range: 10.8 to 35.2 VDC regulated 300 mA maximum |
| Overvoltage Protection | 48 Volt transient protection device |
| Digital (S3 L) | Serial ASCII, TTL level, 9600 bps |
| Accuracy | Determined by sensor |
| Sensitivity | 80 mV @ 5 Hz, mV threshold gradually increasing with frequency |
| Range | 0.5 Hz to 1500 Hz @ TTL level input for open collector |
| Accuracy | ± 0.5% of reading max error @ 25 °C |
| Repeatability | ± 0.2% of reading |
| Resolution | 1 s |
| Update Rate | 150 ms nominal |
| Voltage | +4.9 to 5.5 VDC @ 25 °C, regulated |
| Current | 20 mA max. |
| Short Circuit | Protected |
| Reverse | Polarity Protected |
| Relay Specifications | Dry-Contact Relays (2), Open Collector (1) |
| Form | C, N/A |
| Max. Voltage Rating | 30 VDC or 250 VAC, 30 VDC |
| Max. Current Rating | 5 A 50 mA |
| Hysteresis | Adjustable (absolute in Engineering Units) |
| Latch | Reset in test screen or view mode |
| Delay | 9999.9 seconds (maximum) |
| Test Mode | Set On or Off |
| Maximum Pulse Rate | 400 pulses/minute |
| Volumetric Pulse Width | 0.1 s to 3200 s |
| 4 to 20 mA Current Loop Output | ANSI-ISA 50.00.01 Class H (passive) |
| Output | 1 |
| Span | 3.8 to 21 mA |
| Zero | 4.0 mA factory set; user programmable from 3.8 to 4.2 mA |
| Full Scale | 20.00 mA factory set; user programmable 19.0 to 21.0 mA |
| Accuracy | ± 32 A max. error @ 25 C @ 24 VDC |
| Resolution | 6 A or better |
| Temperature Drift | ± 1 A per °C |
| Power Supply Rejection | ± 1 A per V |
| Isolation | Low voltage (< 48 VAC/DC) |
| Voltage | 10.8 to 35.2 VDC |
| Max. Impedance | 250 @ 12 VDC / 500 @ 18 VDC / 750 @ 24 VDC U |
| Update Rate | 150 ms nominal |
| Adjustable span | Reversible |
| Error Condition | Selectable error condition 3.6 or 22 mA or NONE |
| Test ModeI | ncrement to desired current (range 3.6 to 21.00 mA) |
